Search
Browse Categories
Browse by Manufacturer

TENS & EMS Combo, 5 modes of TENS, 3 Modes of EMS, 100mA output, OTC Display box

Your Price: Only available to healthcare practitioners, healthcare verified log in account required to purchase
Item Number: TENS2N1 OTC Display Box
Manufacturer: Clinical Health Services
Manufacturer Part No: TENS2N1 OTC Display Box
The TENS2N1 gives the user the choice of 5 modes of TENS and 2 Modes of EMS with full strength 100mA output.

System Includes: Stimulator, Lead Wires, 1 package of Self-Adhesive Electrodes, 9V Battery, Instruction Booklet, OTC Display Box Packaging.

Specifications:
Power sources: One 9 volt battery
Output channel: Dual channel
Waveform: Bi-phase square-wave pulse
Output current: 0-50V (Load:500 ohm)
Output intensity: adjustable
Treatment type: TENS and EMS mode
P.W. (Pulse Width): Adjustable, from 50 to 300 μs, 10 μs/step
P.R. (Pulse Rate): Adjustable, from 2 to 150 Hz, 1 Hz/step
Timer: Adjustable, from 1 to 60 minutes or continuous.
On Time: Adjustable, 2~90 seconds,1Sec./step.
Off Time: Adjustable, 0~90 seconds,1Sec./step.
Ramp Time: Adjustable, 1-8 seconds, 1 Sec./step.
Modes: B (Burst), N (Normal), M (Modulation) SD1 (Strength Duration) SD2 ,S(Synchronous) and A(Alternate).
Burst Mode: Burst rate: adjustable, 0.5 - 5 Hz,
Pulse width: adjustable, 50~300 μs
Frequency: fixed = 100 Hz
Normal Mode: The pulse rate and pulse width are adjustable. It generates continuous stimulation based on the setting value.
Modulation Mode: Modulation mode is a combination of pulse rate and pulse width modulation. The pulse rate and width are automatically varied in a cycle pattern. The pulse width is decreased by 50% from its original setting in the 0.5 second, then the pulse rate is decreased by 50% from its original setting in the 0.5 second. Total cycle time is 1 second. In this mode, pulse rate (2~150Hz) and pulse width (50-300μs) are fully adjustable.
SD1 Mode: The SD1(Strength-Duration) mode consists of automatic modulation intensity and pulse width in 40% range. The intensity is always increasing while the pulse width is decreasing and vice versa. The intensity is decreased by 40% while the pulse width is increased by 40% in 5 seconds. In the next 5 seconds, the intensity is increased by 40% while the pulse width is decreased by 40%. Total cycle time is 10 seconds. Pulse rate (2~150Hz) and pulse width (50-300μs) are fully adjustable. 15
SD2 Mode: The SD2 (Strength-Duration) mode consists of automatic modulation intensity and pulse width in 70% range. The intensity and pulse width in 70% range. The intensity is always increasing while the pulse width is decreasing and vice versa. The intensity is decreased by 70% while the pulse width is increasing by 70% in 5 seconds. In the next 5 seconds, the intensity is increased by 70% while the pulse width is decreased by 70%. Total cycle time is 10 seconds. Pulse rate (2~150Hz) and pulse width (50-300μs) are fully adjustable.
Synchronous mode: S t i m u l a t i o n o f b o t h c h a n n e l s o c c u r s synchronously. The “ON” time including R a m p U p ” a n d “ R a m p D o w n ” t i m e . Therefore, the setting of ON Time should be no less than two times of the “Ramp” time in this mode. ON TIME ≥ Ramp up + Ramp down Alternate Mode: The stimulation of the CH2 will occur after the 1st contraction of CH1 is completed. In this mode, the setting of ON Time should be no less than two times of the “Ramp” time. The OFF Time should be equal or more than the ON Time. ON TIME ≥ Ramp up + Ramp down OFF TIME ≥ ON TIME
Patient Compliance Meter: This unit can store 60 sets of operation records. Total recorded time is 999 hours.
Low Battery Indication: A low battery indicator will show up on the LCD when the battery is low
Shopping Cart
Your cart is empty.
Products